add evb_mx_plus support
This commit is contained in:
supowang
271
board/TencentOS_tiny_EVB_MX_Plus/BSP/Src/usart.c
Normal file
271
board/TencentOS_tiny_EVB_MX_Plus/BSP/Src/usart.c
Normal file
@@ -0,0 +1,271 @@
|
||||
/**
|
||||
******************************************************************************
|
||||
* File Name : USART.c
|
||||
* Description : This file provides code for the configuration
|
||||
* of the USART instances.
|
||||
******************************************************************************
|
||||
* @attention
|
||||
*
|
||||
* <h2><center>© Copyright (c) 2019 STMicroelectronics.
|
||||
* All rights reserved.</center></h2>
|
||||
*
|
||||
* This software component is licensed by ST under BSD 3-Clause license,
|
||||
* the "License"; You may not use this file except in compliance with the
|
||||
* License. You may obtain a copy of the License at:
|
||||
* opensource.org/licenses/BSD-3-Clause
|
||||
*
|
||||
******************************************************************************
|
||||
*/
|
||||
|
||||
/* Includes ------------------------------------------------------------------*/
|
||||
#include "usart.h"
|
||||
|
||||
/* USER CODE BEGIN 0 */
|
||||
uint8_t data;
|
||||
/* USER CODE END 0 */
|
||||
|
||||
UART_HandleTypeDef hlpuart1;
|
||||
UART_HandleTypeDef huart1;
|
||||
UART_HandleTypeDef huart2;
|
||||
UART_HandleTypeDef huart3;
|
||||
|
||||
/* LPUART1 init function */
|
||||
|
||||
void MX_LPUART1_UART_Init(void)
|
||||
{
|
||||
hlpuart1.Instance = LPUART1;
|
||||
hlpuart1.Init.BaudRate = 115200;
|
||||
hlpuart1.Init.WordLength = UART_WORDLENGTH_8B;
|
||||
hlpuart1.Init.StopBits = UART_STOPBITS_1;
|
||||
hlpuart1.Init.Parity = UART_PARITY_NONE;
|
||||
hlpuart1.Init.Mode = UART_MODE_TX_RX;
|
||||
hlpuart1.Init.HwFlowCtl = UART_HWCONTROL_NONE;
|
||||
hlpuart1.Init.OneBitSampling = UART_ONE_BIT_SAMPLE_DISABLE;
|
||||
hlpuart1.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;
|
||||
if (HAL_UART_Init(&hlpuart1) != HAL_OK)
|
||||
{
|
||||
Error_Handler();
|
||||
}
|
||||
HAL_UART_Receive_IT(&hlpuart1, &data, 1);
|
||||
}
|
||||
/* USART1 init function */
|
||||
|
||||
void MX_USART1_UART_Init(void)
|
||||
{
|
||||
|
||||
huart1.Instance = USART1;
|
||||
huart1.Init.BaudRate = 115200;
|
||||
huart1.Init.WordLength = UART_WORDLENGTH_8B;
|
||||
huart1.Init.StopBits = UART_STOPBITS_1;
|
||||
huart1.Init.Parity = UART_PARITY_NONE;
|
||||
huart1.Init.Mode = UART_MODE_TX_RX;
|
||||
huart1.Init.HwFlowCtl = UART_HWCONTROL_NONE;
|
||||
huart1.Init.OverSampling = UART_OVERSAMPLING_16;
|
||||
huart1.Init.OneBitSampling = UART_ONE_BIT_SAMPLE_DISABLE;
|
||||
huart1.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;
|
||||
if (HAL_UART_Init(&huart1) != HAL_OK)
|
||||
{
|
||||
Error_Handler();
|
||||
}
|
||||
|
||||
}
|
||||
|
||||
/* USART2 init function */
|
||||
|
||||
void MX_USART2_UART_Init(void)
|
||||
{
|
||||
|
||||
huart2.Instance = USART2;
|
||||
huart2.Init.BaudRate = 115200;
|
||||
huart2.Init.WordLength = UART_WORDLENGTH_8B;
|
||||
huart2.Init.StopBits = UART_STOPBITS_1;
|
||||
huart2.Init.Parity = UART_PARITY_NONE;
|
||||
huart2.Init.Mode = UART_MODE_TX_RX;
|
||||
huart2.Init.HwFlowCtl = UART_HWCONTROL_NONE;
|
||||
huart2.Init.OverSampling = UART_OVERSAMPLING_16;
|
||||
huart2.Init.OneBitSampling = UART_ONE_BIT_SAMPLE_DISABLE;
|
||||
huart2.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;
|
||||
if (HAL_UART_Init(&huart2) != HAL_OK)
|
||||
{
|
||||
Error_Handler();
|
||||
}
|
||||
|
||||
}
|
||||
/* USART3 init function */
|
||||
|
||||
void MX_USART3_UART_Init(void)
|
||||
{
|
||||
|
||||
huart3.Instance = USART3;
|
||||
huart3.Init.BaudRate = 115200;
|
||||
huart3.Init.WordLength = UART_WORDLENGTH_8B;
|
||||
huart3.Init.StopBits = UART_STOPBITS_1;
|
||||
huart3.Init.Parity = UART_PARITY_NONE;
|
||||
huart3.Init.Mode = UART_MODE_TX_RX;
|
||||
huart3.Init.HwFlowCtl = UART_HWCONTROL_NONE;
|
||||
huart3.Init.OverSampling = UART_OVERSAMPLING_16;
|
||||
huart3.Init.OneBitSampling = UART_ONE_BIT_SAMPLE_DISABLE;
|
||||
huart3.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;
|
||||
if (HAL_UART_Init(&huart3) != HAL_OK)
|
||||
{
|
||||
Error_Handler();
|
||||
}
|
||||
|
||||
}
|
||||
|
||||
void HAL_UART_MspInit(UART_HandleTypeDef* uartHandle)
|
||||
{
|
||||
|
||||
GPIO_InitTypeDef GPIO_InitStruct = {0};
|
||||
if(uartHandle->Instance==LPUART1)
|
||||
{
|
||||
/* USER CODE BEGIN LPUART1_MspInit 0 */
|
||||
|
||||
/* USER CODE END LPUART1_MspInit 0 */
|
||||
/* LPUART1 clock enable */
|
||||
__HAL_RCC_LPUART1_CLK_ENABLE();
|
||||
|
||||
__HAL_RCC_GPIOC_CLK_ENABLE();
|
||||
/**LPUART1 GPIO Configuration
|
||||
PC0 ------> LPUART1_RX
|
||||
PC1 ------> LPUART1_TX
|
||||
*/
|
||||
GPIO_InitStruct.Pin = GPIO_PIN_0|GPIO_PIN_1;
|
||||
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
|
||||
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
||||
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
|
||||
GPIO_InitStruct.Alternate = GPIO_AF8_LPUART1;
|
||||
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
|
||||
|
||||
/* LPUART1 interrupt Init */
|
||||
HAL_NVIC_SetPriority(LPUART1_IRQn, 0, 0);
|
||||
HAL_NVIC_EnableIRQ(LPUART1_IRQn);
|
||||
/* USER CODE BEGIN LPUART1_MspInit 1 */
|
||||
|
||||
/* USER CODE END LPUART1_MspInit 1 */
|
||||
}
|
||||
else if(uartHandle->Instance==USART2)
|
||||
{
|
||||
/* USER CODE BEGIN USART2_MspInit 0 */
|
||||
|
||||
/* USER CODE END USART2_MspInit 0 */
|
||||
/* USART2 clock enable */
|
||||
__HAL_RCC_USART2_CLK_ENABLE();
|
||||
|
||||
__HAL_RCC_GPIOA_CLK_ENABLE();
|
||||
/**USART2 GPIO Configuration
|
||||
PA2 ------> USART2_TX
|
||||
PA3 ------> USART2_RX
|
||||
*/
|
||||
GPIO_InitStruct.Pin = GPIO_PIN_2|GPIO_PIN_3;
|
||||
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
|
||||
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
||||
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
|
||||
GPIO_InitStruct.Alternate = GPIO_AF7_USART2;
|
||||
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
|
||||
|
||||
/* USART2 interrupt Init */
|
||||
HAL_NVIC_SetPriority(USART2_IRQn, 0, 0);
|
||||
HAL_NVIC_EnableIRQ(USART2_IRQn);
|
||||
/* USER CODE BEGIN USART2_MspInit 1 */
|
||||
|
||||
/* USER CODE END USART2_MspInit 1 */
|
||||
}
|
||||
else if(uartHandle->Instance==USART3)
|
||||
{
|
||||
/* USER CODE BEGIN USART3_MspInit 0 */
|
||||
|
||||
/* USER CODE END USART3_MspInit 0 */
|
||||
/* USART3 clock enable */
|
||||
__HAL_RCC_USART3_CLK_ENABLE();
|
||||
|
||||
__HAL_RCC_GPIOC_CLK_ENABLE();
|
||||
/**USART3 GPIO Configuration
|
||||
PC4 ------> USART3_TX
|
||||
PC5 ------> USART3_RX
|
||||
*/
|
||||
GPIO_InitStruct.Pin = GPIO_PIN_4|GPIO_PIN_5;
|
||||
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
|
||||
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
||||
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
|
||||
GPIO_InitStruct.Alternate = GPIO_AF7_USART3;
|
||||
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
|
||||
|
||||
/* USART3 interrupt Init */
|
||||
HAL_NVIC_SetPriority(USART3_IRQn, 0, 0);
|
||||
HAL_NVIC_EnableIRQ(USART3_IRQn);
|
||||
/* USER CODE BEGIN USART3_MspInit 1 */
|
||||
|
||||
/* USER CODE END USART3_MspInit 1 */
|
||||
}
|
||||
}
|
||||
|
||||
void HAL_UART_MspDeInit(UART_HandleTypeDef* uartHandle)
|
||||
{
|
||||
|
||||
if(uartHandle->Instance==LPUART1)
|
||||
{
|
||||
/* USER CODE BEGIN LPUART1_MspDeInit 0 */
|
||||
|
||||
/* USER CODE END LPUART1_MspDeInit 0 */
|
||||
/* Peripheral clock disable */
|
||||
__HAL_RCC_LPUART1_CLK_DISABLE();
|
||||
|
||||
/**LPUART1 GPIO Configuration
|
||||
PC0 ------> LPUART1_RX
|
||||
PC1 ------> LPUART1_TX
|
||||
*/
|
||||
HAL_GPIO_DeInit(GPIOC, GPIO_PIN_0|GPIO_PIN_1);
|
||||
|
||||
/* LPUART1 interrupt Deinit */
|
||||
HAL_NVIC_DisableIRQ(LPUART1_IRQn);
|
||||
/* USER CODE BEGIN LPUART1_MspDeInit 1 */
|
||||
|
||||
/* USER CODE END LPUART1_MspDeInit 1 */
|
||||
}
|
||||
else if(uartHandle->Instance==USART2)
|
||||
{
|
||||
/* USER CODE BEGIN USART2_MspDeInit 0 */
|
||||
|
||||
/* USER CODE END USART2_MspDeInit 0 */
|
||||
/* Peripheral clock disable */
|
||||
__HAL_RCC_USART2_CLK_DISABLE();
|
||||
|
||||
/**USART2 GPIO Configuration
|
||||
PA2 ------> USART2_TX
|
||||
PA3 ------> USART2_RX
|
||||
*/
|
||||
HAL_GPIO_DeInit(GPIOA, GPIO_PIN_2|GPIO_PIN_3);
|
||||
|
||||
/* USART2 interrupt Deinit */
|
||||
HAL_NVIC_DisableIRQ(USART2_IRQn);
|
||||
/* USER CODE BEGIN USART2_MspDeInit 1 */
|
||||
|
||||
/* USER CODE END USART2_MspDeInit 1 */
|
||||
}
|
||||
else if(uartHandle->Instance==USART3)
|
||||
{
|
||||
/* USER CODE BEGIN USART3_MspDeInit 0 */
|
||||
|
||||
/* USER CODE END USART3_MspDeInit 0 */
|
||||
/* Peripheral clock disable */
|
||||
__HAL_RCC_USART3_CLK_DISABLE();
|
||||
|
||||
/**USART3 GPIO Configuration
|
||||
PC4 ------> USART3_TX
|
||||
PC5 ------> USART3_RX
|
||||
*/
|
||||
HAL_GPIO_DeInit(GPIOC, GPIO_PIN_4|GPIO_PIN_5);
|
||||
|
||||
/* USART3 interrupt Deinit */
|
||||
HAL_NVIC_DisableIRQ(USART3_IRQn);
|
||||
/* USER CODE BEGIN USART3_MspDeInit 1 */
|
||||
|
||||
/* USER CODE END USART3_MspDeInit 1 */
|
||||
}
|
||||
}
|
||||
|
||||
/* USER CODE BEGIN 1 */
|
||||
/* USER CODE END 1 */
|
||||
|
||||
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|
||||
Reference in New Issue
Block a user